billtheia Posted March 12, 2008 Share Posted March 12, 2008 I'm having trouble with a few windows. I place them in walls and they insert just fine. Then, later, when I go back to them, the insertion has changed so that the wall break is at the outer edge of window trim rather than at the jamb. This isn't happening with all windows, just some. I've re-inserted them trying to fix the problem but the same thing happened with the new windows. Has anyone else had this problem? Do any of you have an idea why this might be happening? I've attached a pic of the windows in question. Quote Link to comment
billtheia Posted July 16, 2008 Author Share Posted July 16, 2008 Has anyone else run into this? I'm having the problem in another file now. It looks like the wall break moves back to the edge of window trim. See attached pic. Quote Link to comment
gmm18 Posted July 16, 2008 Share Posted July 16, 2008 I think I had this problem when I was making symbols out of windows and then inserting them. So you have this error when inserting a fresh window PIO? Of course a very similar error occurs with cross section VP's at windows with trim...very annoying. Quote Link to comment
billtheia Posted July 17, 2008 Author Share Posted July 17, 2008 I wasn't turning the windows into symbols. I was, however, copying windows from place to place rather than inserting a "fresh" one each time. Could that be the root of my problem? Quote Link to comment
billtheia Posted August 25, 2008 Author Share Posted August 25, 2008 Can anyone help me with this? It's still happening. Now in other files. It's an even bigger problem when interior and exterior trim are different widths. See attached pic. Quote Link to comment
billtheia Posted October 8, 2008 Author Share Posted October 8, 2008 Can the moderator or someone else chime in here? I'm still having this problem and can't for the life of me figure out why. Thanks. Quote Link to comment
CipesDesign Posted October 9, 2008 Share Posted October 9, 2008 Bill, I've seen very similar things often in elevation views, in rendered modes, but never in plan view. So here's a couple questions: 1) Are the screenshots in "top/plan" view (as opposed to "top" which is a 3d view)? 2) Are they in "Wireframe" (as opposed to some other rendered mode)? 3) Have you tried using the "wall heal" tool at (or near) the offending end(s) of the window(s)? 4) Are you absolutely sure that the windows are "in wall", as opposed to just placed in the drawing but not actually inserted? 5) Have you tried quitting VW's and restarting? 6) Have you tried restarting the computer? 6) After restarting, can you open a brand new (as in blank- not a template) file and reproduce the problem?? Hope one of those might help ;-) Oh and BTW, I duplicate windows and doors all the time and I seriously doubt that has anything to do with it. Unless of course there was some really odd corruption in the first one... Quote Link to comment
billtheia Posted October 9, 2008 Author Share Posted October 9, 2008 The views that I posted are in top/plan/2d/wireframe view. I'm using elevation SLVPs and they show the gap also. The doors/windows are "in" the wall. I can't MAKE the problem happen. I place a door/window, work on my drawings, and eventually the gaps appear. It only happens with some of the doors/windows and I can't discern any pattern to it. If I pull the door out of the wall and reinsert it, the problem goes away temporarily but comes back after working in the file for a while. I can also temporarily "fix" the problem if I stretch the end of the wall, insert another door/window, or do any intersection clean-up. This has happened in several files now but I think that they might all have started with the same (or at least a related) template. I submitted a bug report about this but never heard anything from NNA about it. Quote Link to comment
bonus Posted October 9, 2008 Share Posted October 9, 2008 As you can see from my topic "windows from 2008..." I had similar problems and have submitted it as a bug report. I also had a swift answer from NNA asking me to send files to them. I have (as late as yesterday) sent several files and snapshots and am waiting for their reply. My problem is not exactly the same but very similar and affects wall insertion and window detail presentations in particular. I just started using 2009 and thought this was a 2009 problem, but if I go back to 2008, blank documents and all, I can reproduce similar problems - not the same though. At the end I get lost with all the different settings and possible combinations and blame myself for it all...so I'm not too proud to say that I'm glad I'm not alone with these problems. Anyway, I'll tune in and give you all I get from my mail contacts with NNA a.s.a.p. By the way - I'm not sure the problem is with the windows. I have a feeling the walls might be the root, because I have walls randomly loosing their "join-with-other-walls function". Also very annoying. Quote Link to comment
billtheia Posted August 19, 2009 Author Share Posted August 19, 2009 Has anyone else experienced this problem and/or found a solution? I'm still having the same issue with window fill not going to the window jamb when trim is included. See new attachment. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.