switchonet Posted January 22, 2021 Share Posted January 22, 2021 Hello, where can I adjust to distance between the sockets when I create them. When I use the socket tool "along line" I get in the vertical direction every step a new socket. In the horizontal direction I only get a socket evry second step but also want to have it for every step. Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 22, 2021 Vectorworks, Inc Employee Share Posted January 22, 2021 Hi, Sockets are spaced on multiples of the snap grid setting. The horizontal spacing is greater because you mostly need room for the socket name to be displayed. This is an exercise is pleasing most of the people most of the time. Conrad Quote Link to comment
switchonet Posted January 25, 2021 Author Share Posted January 25, 2021 Ok. I understand but I roatated the text blocks so it is like the horizontal symbols and now It would be great to change the spacing otherwise I cannot use the along line tool and use the move and copy. after it I can use the spotlight numbering or the connectCAD socket numbering. I hoped I could change someweher the space and simple have not found it. But do not worry I have a work-around. Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 25, 2021 Vectorworks, Inc Employee Share Posted January 25, 2021 Ah now I get it. I'll add this point to my notes. Good that you have a workaround though because I think we have more than enough already in terms of new stuff to test. Conrad Quote Link to comment
switchonet Posted January 25, 2021 Author Share Posted January 25, 2021 Yes, the only problem is that a part of the text or the whole text disapear. But when you are zooming you can see the information. I even tried with fill the textblock, this works for one information but not fpr the second text block. When you are using it not rotated it is no problem. Quote Link to comment
switchonet Posted January 25, 2021 Author Share Posted January 25, 2021 When you are opening the device everything is fine. Quote Link to comment
Thomas K. Posted January 27, 2021 Share Posted January 27, 2021 Same here. When I zoom in an d out the text shows up. When i don't zoom you can only see the first letter. Opening the device doesn't make a different. Testet with clean osx and clean vwx installation. newest service pack etc. Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 Ok, these are things for us to think about... But just to manage expectations a bit - there is always a risk of unexpected results when you start using things in ways they weren't designed for. If it works that's great but if it doesn't then that's not necessarily wrong either. The bottom line here is that you want the option for text to run vertically in these cases so as to achieve a closer socket spacing. That's what I take away from this discussion as an improvement to be considered. Conrad Quote Link to comment
Thomas K. Posted January 27, 2021 Share Posted January 27, 2021 One more thing to point at: when i change the angle of the external to 90 degrees, the text nearly disapears. Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 Y e s T h o m a s we didn't anticipate v e r t i c a l E x t e r n a l s Conrad Quote Link to comment
Thomas K. Posted January 27, 2021 Share Posted January 27, 2021 1 minute ago, Conrad Preen said: Y e s T h o m a s we didn't anticipate v v v i'm sorry!! Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 It's a bit hard to read... Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 Never mind I added it to the wish list. C Quote Link to comment
Vectorworks, Inc Employee Nikolay Zhelyazkov Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 @Conrad Preen, @Kelzilla1000, Hello guys, The disappearing text is more like rendering issue, since the text is visible when zooming in/out. What is more, turning unified view on fixes this. Best Regards, Nikolay Zhelyazkov Quote Link to comment
Vectorworks, Inc Employee Conrad Preen Posted January 27, 2021 Vectorworks, Inc Employee Share Posted January 27, 2021 @Nikolay Zhelyazkov good to know! But rotating sockets still isn't "as-designed", otherwise we could do away with orientation altogether. Hmmm! Could be an idea? 😄 C Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.