Jim Smith Posted October 5, 2018 Share Posted October 5, 2018 A lot of nice improvements so kudos for the upgrades! Especially like the improved launch time & faster renders. Still a fly or three in the ointment here & there: - Notification crashes VW when selected - The Quick Keys to align the change in wall types has never been re-instated (since it was removed in VW 2014?) - Still can't control the output of the Interior Elevation Marker to eliminate the Sheet # or customize the marker - Gird Bubble tool is still not ready for prime time - Spelling does not migrate to the new version so the first few files will take longer to spell check ( & it's not just COLOUR, lots of common short forms need to be reentered) 1 Quote Link to comment
David S Posted October 10, 2018 Share Posted October 10, 2018 I'm a service pack 1 man myself @Jim Smith so today's the day!! Quote Link to comment
Jim Smith Posted October 10, 2018 Author Share Posted October 10, 2018 SP-1 Installed - Selecting Notification Icon still causes VW to crash. I did notice there was a notification yesterday; was that about SP-1? Quote Link to comment
Kevin McAllister Posted October 10, 2018 Share Posted October 10, 2018 2 minutes ago, Jim Smith said: SP-1 Installed - Selecting Notification Icon still causes VW to crash. I did notice there was a notification yesterday; was that about SP-1? ^ yes, it was a notification about SP1. KM Quote Link to comment
Vectorworks, Inc Employee PVA - Admin Posted October 10, 2018 Vectorworks, Inc Employee Share Posted October 10, 2018 2 minutes ago, Jim Smith said: was that about SP-1? It was. 2 minutes ago, Jim Smith said: Selecting Notification Icon still causes VW to crash. I still can not get the message center to crash here, however I heard it happened to one of our sales people, I'm going to pay him a visit. Quote Link to comment
Jim Smith Posted October 10, 2018 Author Share Posted October 10, 2018 (edited) Thanks. This happens on both a brand new blank file as well as a batch converted file. Edited October 10, 2018 by Jim Smith Quote Link to comment
Jim Smith Posted October 10, 2018 Author Share Posted October 10, 2018 I just tried this: Changed my Workspace to Architect from my custom Workspace. Restarted Programme. Notification Still hangs up the programme. Quote Link to comment
Jim Smith Posted October 16, 2018 Author Share Posted October 16, 2018 (edited) I note that VW2019 doesn't "remember" where to open a file when using two Monitors. In 2018 VW did remember where to open the file. Edited October 16, 2018 by Jim Smith Quote Link to comment
David S Posted October 16, 2018 Share Posted October 16, 2018 I'm a week in to 2019 SP1 now Jim x2 and everyone. I trial it (survey production in 3d) before rolling it out to our 4 x licenses. I have to say I've found it to be very tactile and user friendly compared to 18. I've had little time to mess about but the clip cube viewport is a gods-send and will save so much time. I havent had too many issues but there are a few! Sometimes it seems to "forget" and needs re-booting. Sometimes roofs/floors go unsolid for no reason (save, close, open, ok again) . On one occasion the layer model produced ghost walls I had not built copied from one design layer to another! (save, close, open, ok again) It's always hard changing over in the middle of a day job but I will provide feedback as I can. Cheers D Quote Link to comment
Cadplan Architecture Posted October 16, 2018 Share Posted October 16, 2018 (edited) On 10/5/2018 at 8:19 PM, Jim Smith said: A lot of nice improvements so kudos for the upgrades! Especially like the improved launch time & faster renders. Still a fly or three in the ointment here & there: - Notification crashes VW when selected - The Quick Keys to align the change in wall types has never been re-instated (since it was removed in VW 2014?) - Still can't control the output of the Interior Elevation Marker to eliminate the Sheet # or customize the marker - Gird Bubble tool is still not ready for prime time - Spelling does not migrate to the new version so the first few files will take longer to spell check ( & it's not just COLOUR, lots of common short forms need to be reentered) Does it have a new door tool to allow custom bi-folding patio doors? Does it have an improved stair tool? Edited October 16, 2018 by Cadplan Architecture Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.