barkest Posted May 10, 2016 Share Posted May 10, 2016 thanks for the reply I created a DLVP and with it selected I create a new SLVP but the SLVP does not carry over the clip. I doesn't create on top of the DLVP Is the process: Create the DVLP (works fine) With the DVLP selected then View > Create Viewport (using a sheet layer) thanks Quote Link to comment
line-weight Posted May 10, 2016 Share Posted May 10, 2016 I meant, it might be creating a SLVP on top of another, pre-existing SLVP (this is what was happening to me until I worked it out). I don't think you need to have the DLVP selected when you "create viewport". Just make sure the relevant DL is active. Does that work? Quote Link to comment
barkest Posted May 10, 2016 Share Posted May 10, 2016 Thanks Col - got it now and its working I had no idea you could do this and I will use it quite a bit thanks again Quote Link to comment
line-weight Posted May 10, 2016 Share Posted May 10, 2016 (edited) It took me quite a bit of messing around to work out how to do it. I think this might be an example of a feature that's slightly accidental, but potentially very useful, but the VW designers don't realise it is, or why it is. And therefore, while it's possible, it's messy to use. It's something the implementation of which could be much improved in future releases, perhaps with minimal development input relative to usefulness to VW users. Edited May 10, 2016 by col37400 Quote Link to comment
Phil hunt Posted May 10, 2016 Author Share Posted May 10, 2016 errrmmm struggling to make this work do you create the clip cube in an iso and then create a section viewport on the top or the sides of the model so this appears on a sheet layer i tried to change the view on the oip in the sheetlayer to no avail thanks Quote Link to comment
barkest Posted May 10, 2016 Share Posted May 10, 2016 set up you view in a DL then use the clip cube to clip. When you are happy with this then right-click on the clip cube to create a section viewport. Create this on a new DL. You now have a DLVP. Just create a SLVP (View > Create Viewport). Place onto a new SL to make sure you don't have a copy anywhere thats it Quote Link to comment
line-weight Posted May 10, 2016 Share Posted May 10, 2016 errrmmm struggling to make this work do you create the clip cube in an iso and then create a section viewport on the top or the sides of the model so this appears on a sheet layer i tried to change the view on the oip in the sheetlayer to no avail thanks Go into the relevant design layer and get your view of your model into iso or perspective as you wish. Activate the clip cube and position the section where you want it. Then select the clip cube and highlight one of its faces (the one you want to use for the section). That face will glow red. Right click on it and create a *design layer* viewport. You might want to make a special design layer just for this purpose to keep things simple. Then go to that design layer - the one where you've just created the new design layer viewport. You should see the sectioned version of your model. You can now use the flyover tool or other methods to get the view you want. Iso or perspective. Once you have the view you want, now create a *sheet layer" viewport on a sheet layer of your choice. I think you can sort of adjust the viewpoint from the OIP of the sheet layer viewport, but it doesn't work very well. Seems better to get the viewpoint you want whilst looking at the design layer viewport. Before creating the sheet layer viewport. Quote Link to comment
Phil hunt Posted May 10, 2016 Author Share Posted May 10, 2016 got it wasn't creating the clipcube on a design layer cheers for that this is exactly what i wanted going to use this all the time can't understand in the clip cube mode and say a perspective view you cant action this to go straight to a viewport seem so obvious never know 2017 vw release !!!!!!! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.