Jump to content
Sign in to follow this  
Ken

Fillet edge of cylinder

Recommended Posts

So it works for you? It's not working for me for a cylinder. That's what I'm saying.

Share this post


Link to post

The cylinder I first posted didn't take the fillet. But here's my real project where it's not working. The cylinder is actually not straight. Both inside and outside diameters taper, as in "draft" for injection molding. Hopefully not too complicated for fillet? I've got many more instances that are more complicated.

fICNHYK.jpg

Share this post


Link to post

Ken,

How are you creating the cylinder? It has a lot of facets which may be causing the trouble you're experiencing. Did you use a multiple extrude? That's one method of construction I tend to avoid.

Kevin

Share this post


Link to post

Yes I had to use multiple extrude for both inside cylinder (the void) and outside. How else to produce a tapered cylinder? But more to the problem, why can't the resulting edges take fillet?

Is fillet very limited?

If so, what other method is available to ease the edges of compound solids?

Share this post


Link to post

One way to form the cylinder is to draw your 2d wall section profile (just one side) and sweep it around a locus at the axis. 2d objects in Top/Plan. The sweep will emerge with axis parallel to the z axis. This shape will take the fillet. Or better, draw the fillets into the sweep profile.

Another way is to draw the inner and outer circles at bottom, convert them to NURBS (This makes a group containing 2 NURBS curves), Duplicate in Place, Raise the second set to proper z height, Rescale the upper group (or just draw the second set at correct radii). Ungroup all, Loft surface from bottom outer>top outer>top inner>bottom inner. In the Loft dialog, select Ruled, Closed, Create Solid, Keep Curves. This creates a Generic Solid which will accept the Fillet.

Post back if not familiar with these techniques.

-B ubbthreads.php?ubb=download&Number=10067&filename=Sweep.png

ubbthreads.php?ubb=download&Number=10068&filename=Loft.png

Edited by Benson Shaw

Share this post


Link to post

Ken,

I think its because it sees each segment as a separate surface so often the segments won't be big enough for your fillet radius and it fails. Sweeps and solids are much better behaved. Benson's methods will work. You could also use a pair of tapered extrudes, subtracting one from the other to create the hole.

I don't think the multiple extrude object has been updated for many versions. It may not take advantage of the Parasolid engine (its a guess but nothing else produces facetted geometry in quite the same way).

Kevin

Share this post


Link to post

Ken et al - there is a better and more effective way to model this:

Step 1 - draw the base circle.

Step 2 - use Tapered Extrude to get the base 3d object.

Step 3 - use Shell to turn the shape into a tapered tube.

Step 4 - use the fillet tool to round the top edges.

Step 3 Note:

- use the Option key to select the bottom surface.

- use the Shift key to add the top surface to the selection set.

The process is shown in the attached image and file.

Using the correct techniques can make a big difference to the modelling outcome in Vectorworks. The 3D Power Pack pages can show you what to use and when. Take the time to explore all of the information available and your modelling will significantly improve.

http://www.vectorworks.net/3Dpowerpack/qtexamples.php

Share this post


Link to post

hi mike i notice your shell solid went all the way through the model when i do it say to 10mm I'm left with 10mm solid at one end of the object do you have to trim that section away to give you a clear hole all the way ?

Share this post


Link to post

You select the surfaces that you want open.

First you select the bottom surface (depressing the option key allows you to select surfaces that are behind other surfaces). Then with the Shift key depressed you click on the top surface to add that to the selection set.

The attached image shows the tapered extrude with two surfaces selected.

Share this post


Link to post

It's a good exercise.

But I'm finding Tapered Extrude not working sometimes. This is just a simple circle drawn on a layer that has many other objects.

p98w1fx.jpg

Besides, the desired taper is reversed on the inside.

kdabd7J.jpg

Share this post


Link to post

Ken try doing two tapered extrudes and then use Subtract Solid to form the 3D object.

With Tapered Extrude:

- the base 2D shape needs to be Layer Plane

- positive angles taper the object inwards

- negative angles taper the object outwards

To get a larger top and a smaller bottom you can also use a positive angle with a negative extrude. You would then need to move the inner 3D object upwards by the height of the extrude.

Share this post


Link to post

Experiment with Benson's two methods and my one method and decide which works best for you. They all produce valid workable results.

Share this post


Link to post

With Tapered Extrude:

- the base 2D shape needs to be Layer Plane

Good tip, Mike.

For some reason, my document is drawing new lines, circles, rectangles, etc in Screen Plane mode by default. The Document Prefs / Plane Mode is set to Screen Plane or Working Plane. But the same pref settings in another document (or new blank document) defaults, as desired, with drawings created in Layer Plane mode. This is the problem causing my Tapered Extrude from not working.

What other factors influence the pref settings?

Share this post


Link to post

Ken, I'm not sure why the 2D source shape for a Tapered Extrude has to be a Layer Plane object. The best way to deal with it is to draw your 2D shape and then change it to Layer Plane on the OIP.

Share this post


Link to post

OH yes, this thread is so very very helpful on so many levels.

Thanks to all who have contributed!

Share this post


Link to post

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

 

7150 Riverwood Drive, Columbia, Maryland 21046, USA   |   Contact Us:   410-290-5114

 

© 2018 Vectorworks, Inc. All Rights Reserved. Vectorworks, Inc. is part of the Nemetschek Group.

×
×
  • Create New...