Jump to content

Mike Wright

  • Content Count

  • Joined

  • Last visited

Community Reputation

19 Good


About Mike Wright

  • Rank

Personal Information

  • Location
    United Kingdom

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Mike Wright

    Bridle tool problem

    When I create a bridle (simple 2 leg to a structural member in this case) the auto select tool picks the correct objects as below: But when the bridle builds it is at the wrong height: Am I doing something wrong? VX2019 SP3.1 Windows 10
  2. Mike Wright

    LED wall looks dim, truss looks basic, no detail

    you have the 'simplified' class visible for your truss. Hide this class in the viewport proprieties and your truss detail will return
  3. Mike Wright

    Modelling an LED screen

    *similar disclaimer* I am also not an engineer Here is a demonstration of my theory. On the left is a truss object created to be the same weight and dimensions as a theoretical screen . It has a rigid cross section because as near as damn it that is how an LED screen behaves. This is coupled to the truss using a truss link with a rigid cross section (mimicking say a half coupler*). All but the end two links are in compression and have failed. In reality this would prevent the truss from deflecting as expected unless you were using a pliable method of supporting the screen (spanset etc). On the right is a distributed load of the same weight showing the correct deflection of the truss. So in theory: If I use a rigid connection between header bar and supporting truss, I prevent the truss from deflecting. Which braceworks cannot model. If I use a soft connection between header bar and supporting truss the load will be almost exclusively applied at the outer most connections where the deflection of the truss and the screen are equal. Now in answer to my own original question: I have spaced my mother grid and the hoists that support the circular truss to minimise the variance in deflection around the circumference. I have achieved this without the need to apply any chain shortening as without load cells this will be wildly inaccurate in practice. This means that in theory none of the supports between screen header and circular truss should be wildly in compression (the screen here is modelled as a distributed load applied direct to the circular truss) : There are factors like for instance adding additional hoists which can cause this deflection to vary massively and in this case chain shortening is the only option to restore the desired flat support truss: My conclusion has been that to most accurately match theory to practice, my truss deflection must be as uniform as possible under FEA like Braceworks. Excuse the lengthy rambling post but (especially given recent events) I am taking a personal (and have been asked to take a corporate) interest in the rigging of LED screens and am interested in peoples opinions. I'm happy to have holes picked in any of the above or to be proven completely wrong! *Pro Burger for those on the other side of the pond
  4. Mike Wright

    Modelling an LED screen

    I've a relatively complex rig where I'm very close to my loading limits for the roof. One of the key elements of the rig is a large circular LED screen suspended from a circular truss. Currently I have the screen modelled as a series of point loads, one for every pick up on the screen header bars. My though is that this in no way reflects how a screen actually behaves as it is an inherently rigid structure attached to one which deforms under load. Could I produce a custom 'truss' which replicates the screen header bar but has a rigid cross section and the same weight/m as the screen itself. This could then be 'attached' to the circular truss using multiple pliable truss cross points to give a more accurate transfer of forces (the screen header will be rigged using round slings from the truss) Any thought would be gratefully received
  5. Mike Wright

    2019 SP3 strange DWG import behaviour

    solved - for some reason it had been set to convert all objects to 2D
  6. Mike Wright

    Viewport from clip cube not functioning

    Thanks I've worked out that clip cube only works with OpenGL and RW rendering and also appears without the clip cube until it's rendered
  7. I am unable to get the viewport from clip cube to work. I have 'display with clip cube' ticked when I create the viewport but it always appears on the sheet layer without. I'm sure I am doing nothing wrong VW2019 SP3.1, Windows 10
  8. I have been struggling to import a DWG model into VWX. this the result of an import into VWX2019: And this is the same model imported into VWX2018: There is a lot of detail missing from the 2019 import but I haven't changed any settings away from my normal import process PC system
  9. Brilliant! That menu has always evaded me. It's not very obvious. Thanks
  10. Thanks Is there a way of adjusting this property once a worksheet is generated?
  11. When I convert my trusses to lighting positions they no longer appear in my truss count worksheets. Am I doing something wrong?
  12. Mike Wright

    Vectorworks 2019 SP1 Updater Not Working

    I have been in touch with tech support and they have provided me with links direct to the installers for for Vectorworks Updater, once installed this works fine for SP3 although I had to insert the license number myself Mac http://release.vectorworks.net/nnapub/updaters/24/NNA/eng/app/Vectorworks 2019 Updater-24.0.477321-mac.zip Windows http://release.vectorworks.net/nnapub/updaters/24/NNA/eng/app/Vectorworks 2019 Updater-24.0.477321-win-installer.exe
  13. Mike Wright

    Another problem with trusses

    You'll have to build your own spacers, the prolyte spacers in the libraries do not work
  14. Mike Wright

    The problem with the simplified display of trusses

    that rotation also happens randomly sometimes when connecting trusses, especially at corner blocks I think I reported it as a bug a while ago
  15. Mike Wright

    Vectorworks 2019 SP1 Updater Not Working

    SP3 and updater still does not work


7150 Riverwood Drive, Columbia, Maryland 21046, USA   |   Contact Us:   410-290-5114


© 2018 Vectorworks, Inc. All Rights Reserved. Vectorworks, Inc. is part of the Nemetschek Group.